Toolroom and inspection equipment for the manufacturing industry by Anton Tools.

Specifications

•	Ideal for the finest tool room and production work. Provides positive grip for layout, machining and inspection
•	Clamps provide true tangential contact of cylindrical work. No clamp interference when V-Block lies on either side.
•	Material: High quality steel alloy
•	Hardened to Rock 56-60.
•	Aged for permanent accuracy.

•

90 degree V is held central to sides in VBH-01 and VBH-02 to .0002 T.I.R. also only .0002 between 2 or more matched blocks (that means only .0001 off center) r 90 degree V is held central to sides in VB-03, VB-04, and VB-05 to .0003 T.I.R. also only .0003 between 2 or more matched blocks (that means .00015 off center).

•

90 degree V is held parallel to bottom in VBH-01 and VBH-02 to .0002 T.I.R.

•

90 degree V is held parallel to bottom in VBH-03, VBH-04, and VBH-05 to .0003 T.I.R.

•

Clearance holes in bottom for mounting V-Blocks on angle plates, face plates, etc.

•

Two tapped holes provided for mounting V-Blocks perpendicular to face plates, etc.

•

A few additional uses: as spacing blocks on jig borers; for stacking (with matched blocks); for accurate set-ups; as angle plates; as two-way angle plates (with Anton Adjust-O-Clamp); as parallels, etc.

•

90 degree V is held square to the ends to .0002 T.I.R. for VBH-01 and VBH-02; to .0003 T.I.R. for VBH-03, VBH-04, and VBH-05 from a master square rod.

•

All sides are square to .0002 from a master square.

•

All sides are parallel to .0001 T.I.R. for VBH-01 and VBH-02; to .0002 T.I.R. for VBH-03, VBH-04, and VBH-05.

•

Total size tolerance between 2 or more matched blocks .0001 for VBH-01 and VBH-02; .002 for VBH-03, VBH-04, and VBH-05.

•

Two or more matched blocks are marked for identification.

PART #	WORK HOLDING CAPACITY	DIMENSION IN INCHES			APPROX. WEIGHT PER PIECE
		WIDTH	HEIGHT	LENGTH

VB-10

1" Dia.

1-5/8

1-1/2

3/4

lb.

VB-20

2" Dia.

1-5/8

2-1/2

2-3/4

lbs.

VB-30

3" Dia.

4-1/4

2-1/2

3-3/8

7-1/2

lbs.

VB-40

4" Dia.

5-1/4

2-1/2

3-3/8

9-1/4

lbs.

•

Clamps provide true tangential contact of cylindrical work. No clamp interferance when V-Block lies on either side.

•

Provides positive grip.

•

Clearance holes in bottom for mounting V-Blocks on angle irons, face plates, etc.

•

90 degree V is held central with the sides, parallel with the bottom and square with the ends within .0005*. All sides are square with each other within .0004*.

These V-Blocks include one clamp and two screws. Extras are available.

PART #	WORK HOLDING CAPACITY	DIMENSION IN INCHES			APPROX. WEIGHT PER PIECE
		WIDTH	HEIGHT	LENGTH

VB-100

1" Dia.

1-5/8

1-1/2

1/2

lb.

VB-200

2" Dia.

1-5/8

2-1/2

lbs.

VB-300

3" Dia.

4-1/4

2-1/2

3-3/8

lbs.

VB-400

4" Dia.

5-1/4

2-1/2

3-3/8

8-3/4

lbs.

•

90 degree V is held central with the sides, parallel with the bottom and square with the ends within .0005*. All sides are square with each other within .0004*.

•

Low cost method for tool room, inspection, and production work.

•

Holes can be drilled and tapped in bottom for mounting V-Blocks on angle irons, face plates, etc. as required.

These V-Blocks are Plain Steel V-Blocks. There are no clamps or screws.

PART #

FITS V-BLOCK

CAPACITY

WEIGHT PER CLAMP

AOC-VB-1	VBH-01	Up to 5/8" Square	1/4 lb.
	VB-10
	VBH-100

AOC-VB-1	VBH-03	Up to1-3/4" Square	1-1/4 lb.
	VB-30
	VBH-300

Specifications... Anton Adjust-O-Clamp is designed to save time on grinding 1 side square to 2 other sides to .0001 accuracy without indicators. Center screw position for use with cylindrical work pieces.